Drayton Dubs
Would you like to react to this message? Create an account in a few clicks or log in to continue.



 
HomeLatest imagesSearchRegisterLog in

Share
 

 Water blockage on my 89 MK2 Golf

View previous topic View next topic Go down 
AuthorMessage
GazEllis83
Slow Starter
Slow Starter
GazEllis83

Posts : 96
Karma : 45
Join date : 2014-07-15
Age : 40
Location : Market Drayton

Water blockage on my 89 MK2 Golf Empty
PostSubject: Water blockage on my 89 MK2 Golf   Water blockage on my 89 MK2 Golf Icon_minitimeSun Aug 10, 2014 8:21 am

swapped engines today and got a slight water blockage. Tried blowing it through and going to remove the thermostat tomorrow to see if that sorts the issue.
has anyone got any tricks tips or advice please?
Cheers
Back to top Go down
https://www.facebook.com/gazsdetailingservice
Colin
Admin
Admin
Colin

Posts : 286
Karma : 79
Join date : 2014-07-13
Location : Over the Rainbow

Water blockage on my 89 MK2 Golf Empty
PostSubject: Re: Water blockage on my 89 MK2 Golf   Water blockage on my 89 MK2 Golf Icon_minitimeSun Aug 10, 2014 9:27 am

Just read this Gaz..............

This procedure is commonly known as "burping" the coolant system. Air can get trapped in your Mk3 because the heater core is located in such a way that air can get trapped. When this occurs, you'll get a rushing or gurgling noise under the dash, possible loss of heat in the cabin, possible bouncing temperature gauge, etc. Ideally, air in the cooling system will be trapped in the radiator top, but because of how the Mk3 cooling system is designed, air can get trapped in the heater circuit or in the thermostat housing.

To remove the air, you have to get the radiator as high as possible compared to the heater core and the rest of the circuit. If you live in San Francisco, or live near the mountains (or have a convenient hill you can drive onto), just find a parking place that a) has the front of the car significantly higher than the back, b) won't freak out if (will) coolant sprays on the ground. If you don't have a natural method of elevating the front, a jack and a couple of jackstands will work too! Just put the front as high as possible. We want the air to get out of trapped areas, such as the thermostat housing and heater core, and into (and out of) the radiator.

NOTE: the coolant in your car is poisonous to kids, pets, wildlife and aquatic life, and is also attractive to such, so PLEASE make sure you flush coolant off the ground and dispose of it properly!

Next, get the bottle of coolant you'll be adding to the engine (trust me, you'll be adding coolant once the air bubbles out). Now that the car is the proper attitude, open the radiator cap (carefully if the engine is hot), and if possible, remove some of the coolant (I use a baster to remove coolant so that it doesn't all bubble out.if the coolant is clean, you can put it into the coolant bottle you've got standing by). Start your car's engine and let it idle until the engine warms up.

Once it gets to operating temperature, turn on your climate control to maximum temperature and fan. If your heater control valve is operating properly, it'll open up and allow coolant to flow through the heater core, and thus, help push the air out (remember, your radiator is now much higher than the core due to the front being so high). Let the car idle for 15-30 minutes and carefully monitor the level of coolant in the radiator. You'll see occasional bubbles (and in some cases, large burps) of air in the radiator. Keep adding coolant slowly (don't add much more than to cover the radiator core until the bubbling slows down. As you reach the 20 minute mark, you should see a steady stream of coolant without bubbles and burps. Top off the radiator at this point, fill the reservoir to the proper level, and replace the radiator cap.


Back to top Go down
https://draytondubsshrops.forumotion.co.uk
Colin
Admin
Admin
Colin

Posts : 286
Karma : 79
Join date : 2014-07-13
Location : Over the Rainbow

Water blockage on my 89 MK2 Golf Empty
PostSubject: Re: Water blockage on my 89 MK2 Golf   Water blockage on my 89 MK2 Golf Icon_minitimeSun Aug 10, 2014 9:33 am

Everywhere I look its always the same advice ...........

Any time you drain the coolant and refill it, you need to start the car and allow it to reach operating temperature with the coolant fill cap OFF. This allows the air to escape and "burp" the system. Also I squeeze the larger coolant hoses with my hands to push/pull the air out of the system, you'll see them come up and out of the bubble. Then turn the car off and allow it to cool completely (15 mins min.) Then refill the coolant if need be.
Back to top Go down
https://draytondubsshrops.forumotion.co.uk
Sponsored content




Water blockage on my 89 MK2 Golf Empty
PostSubject: Re: Water blockage on my 89 MK2 Golf   Water blockage on my 89 MK2 Golf Icon_minitime

Back to top Go down
 

Water blockage on my 89 MK2 Golf

View previous topic View next topic Back to top 
Page 1 of 1

 Similar topics

-
» Revs drop for a few seconds on MK3 Golf
» My MK1 Golf GTI
» name needed for my mk2 golf
» My golf's all sorted
» GOLF MK2 NATIONAL MEET

Permissions in this forum:You cannot reply to topics in this forum
Drayton Dubs :: Watercooled Technical-